DR5000 DCC Multi-Bus Central Unit

20750

New product

Central unit is combined with all conceivable connection sockets in one housing.

Led Status Lights
USB
LAN and WIFI.

Including adjustable power supply (15 - 24 Volt)

More details

Delivery time approx. 10 days

Product customization

132,50 €

-9,13 €

141,63 €

More info

Features DR5000 Multi-Bus Central

Connection options:

Default:

USB
- Communication with computer / control program
- Protocol L.NET or XpressNet V3
- Virtual COM port, speed 9600, 19200, 38400, 56800 or 115200 baud
- Firmware updates

L.NET T
- Interface for L.NET accessories: (controls, feedback, etc.)

L-NET B
- Interface for L.NET accessories: (manual) controls, feedback, etc. Max. 12v / 1000mA
- Interface for L.NET accessories including booster (rail-sync). Max. 12v / 600mA

X SOCKET / R SOCKET
- Interface for Xpress accessories: MultiMouse, LH 100 etc. Max. 12v / 1000mA
- Interface for R-BUS feedback modules

B-JACK
Interface for ROCO boosters, e.g. the MultiMouse Amplifier 10764 can be used as a booster on the DR5000

RS JACK
- Interface for Lenz-RS-connector feedback.

ext88N
- Interface for s88N receivers. Max. 16 x 16 input modules (256 inputs)
- Interface for DR502Xext modules (bidirectional)

Track output
 - DCC track output. Max. 19V / 3.2Amp. Lower voltage possible by other supply. Min. 14V

Programming track output
- DCC programming track output. Max. 19V / 800mA
Switches automatically from track output to programming track output so that the programming track can also be used.

LAN
- 100BaseT Ethernet. Can be connected to a local network using DHCP.

WiFi / WLAN

- bgn wireless network via internal antenna
- Both networks can be reached via UDP / IP and TCP / IP
- Protocols: LenzXpressNetz and / or L.NET-TCP / IP
- Wifi / LAN settings via web interface
- The WiFi / LANB module can serve as an AP (access point) also as a router between the DR5000 WiFi and the home network (LAN)

 

Service:


Stop
- Switch off the track output

Go
- Switch on the track output

- Both switches can also change various simple settings

IR receiver
- Infrared receiver compatible with Uhlenbrock IRIS and Piko DigiFern (or other RC5 / 36Khz remote controls)
- 4 channels, per channel 1 direct locomotive and 4 points direct control / switching

- Further operation possible by means of X-BUCHSE and / or L.NET (hand) controls, the DR502xEXT modules or through the USB / LAN / Wifi interfaces

 

 

LEDs:


STATUS
- Power: supply voltage present; Routing Indication
- Load: Initial load, intensity increases with load. Off = no load
- Short circuit: flashing code indicates which socket caused the short circuit; continuous one is track output

USB
- TX: Data is being sent to the computer
- RX: Data is being received from the computer

INFRARED
- RX: Valid IR data is received

X-JACK
- TX: Data is sent to the X-SOCKET
- RX: Data is received from the X-SOCKET

STOP
- Track output and booster connection are off

GO
- Track output and booster connection are on

L.NET
- TX: Data is sent to the L.NETZ
- RX: Data from the L.NETZ are received

ext88
- At least 1 input on the s88 socket is active; Intensity increases with the number of active inputs

WiFi
- Active: The network is active

LAN
- Link: The LAN is connected and has a connection to a switch / router

ROUTER
- Status: The internal router is active

 

 

DCC:


locomotives
- 126 simultaneous operation / control of locomotives
- F0 - F28
- 14/28/128 Driving steps
- Long and short addresses. (9999 for long, set maximum short address from 0-127)

give way
- 2048 Switches
- Offset + 4 / -4 for MultiMaus Comptability

 

 

General:


feedback
- maximum of 2048 feedback inputs possible

protocol conversion
- All protocols are translated into an internal protocol. Each socket and each port will then have its own protocol

power adapter
- Including low-loss, adjustable external power supply. (15-24 volts)